- #NEW HARD DRIVE FOR IMAC HOW TO#
- #NEW HARD DRIVE FOR IMAC INSTALL#
- #NEW HARD DRIVE FOR IMAC UPGRADE#
- #NEW HARD DRIVE FOR IMAC PRO#
All material provided within this Youtube channel is for informational, educational, & entertainment purposes only. TheBeefmaster assumes no liability for property damage or injury incurred as a result of any of the information contained in this video.
![new hard drive for imac new hard drive for imac](http://img-aws.ehowcdn.com/615x200/cme/cme_public_images/www_ehow_com/i.ehow.com/images/a06/fo/2v/replace-hard-drive-imac-800x800.jpg)
#NEW HARD DRIVE FOR IMAC UPGRADE#
To upgrade your old iMac HDD with an SSD, watch this video: ?
#NEW HARD DRIVE FOR IMAC PRO#
To upgrade an old Macbook Pro battery, RAM and SSD, watch this video: ? This will work for older macbook pros as well. This is the best brand of tool kits for tear downs and electronic repairs: ? Sabrent SATA to USB External Enclosure: ? The last optional step would be to clone your existing installation over or use the migration assistant to transfer your files over to the new SSD with a SATA to USB adapter. We replace the gaskets and seal up the iMac after verifying the installation.
#NEW HARD DRIVE FOR IMAC INSTALL#
We format the drive and then install macOS. Here we perform an upgrade on the iMac by removing the gaskets around the screen, cleaning out any fans in the system, removing the existing hard drive, and then replacing it with a solid-state drive. SATA to USB 3.0 Adapter cable (for data transfer) Medium / Small Screwdriver, “+” cross (Phillips) Painters Tape for holding screen to frame The complete set of replacement adhesive strips are specifically cut to fit 21.5" iMacs from Late 2012 through 2019. SSD of your choice (SATA Connector, 6.0Gb/s V-NAND MLC or TLC) However, the 21.5-Inch "Late 2013" iMac models do have the connector for a PCIe-based "blade" but subsequent 21.5-Inch models like the entry-level iMac "Core i5" 1.4 21.5-Inch (Mid-2014) and the 21.5-Inch "Late 2015" models do not have the connector for a PCIe-based "blade" SSD if one is not installed at the time of initial system purchase.īy contrast, the 27-Inch "Late 2012" and "Late 2013" as well as the "Late 2014" and "Mid-2015" Retina/5K iMac models all have this connector on the motherboard even if the system only is configured with a hard drive at the time of purchase, so it is possible to add a PCIe-based "adapted blade" SSD to these models after the initial system purchase. Unfortunately, if the system only was configured with a hard drive, the needed connector is not present on the motherboard and there is not a way to add a PCIe-based "blade" SSD afterwards. Specifically, if the 21.5-Inch "Late 2012" or "Early 2013" iMac models were configured with an SSD or a "Fusion Drive" at the time of purchase, the SSD module is connected via a dedicated PCIe connector and another m.2 “adapted” SSD can be installed in its place. Note: Some systems support a smaller PCIe-based “blade” SSD, as well. We used a brand new Samsung Evo 860 V-NAND MLC 500GB Solid State Drive with a SATA 6Gb/s Connector. Goal: To increase the iMac’s speed and longevity, while decreasing the time it takes to boot up and load your files.
#NEW HARD DRIVE FOR IMAC HOW TO#
Hopefully this either resolves the issue or identifies where the fault is.A detailed video with instructions on how to remove the screen of your 21.5” iMac in order to upgrade the internal hard disk drive (HDD) to a SATA connected Solid State Drive (SSD)
![new hard drive for imac new hard drive for imac](https://i.ytimg.com/vi/_FkSBsscg90/maxresdefault.jpg)
Press and hold the power button for 5 seconds.Unplug the computer's power cord and all peripherals.With the new hard drive still installed, attempt an SMC reset as well as a PRAM/NVRAM reset.Reinstall the new hard drive and try again.Connect the new hard drive to another computer (if available, either by installing or using a SATA to USB/FW adapter) - this will let you know if the new drive is functioning.Reinstall the original hard drive and verify that it shows up in Disk Utility - this will let you know that the SATA cables and connections on the logic board are functioning.It would be odd to see that but it is certainly possible. Was the hard drive simply an upgrade or is it to replace a failed/failing hard drive? It's possible that the new hard drive is defective. With that in mind I would be troubleshooting the component itself. This hard drive shows as using the SATA II specification, which is backwards compatible with the SATA I specification. The early Intel iMacs used the SATA I specification of 1.5Gbit/s. This hard drive SHOULD be compatible with your iMac assuming you do have a 17" Intel iMac.